|
These are basic drillings and are recommendations
to provide a starting point from which to obtain variations in ball
performance. As with any Symmetric core configuration, these balls
can be drilled many different ways and can be fine tuned to meet the
needs of an individual bowler. Do not hesitate to adjust the drill
pattern to match the lane conditions and the bowler's own characteristics
such as ball speed, revolutions and axis rotation.
The illustrations of the drill patterns show the
Pin, CG (Center of Gravity), PAP (Bowler's Positive Axis Point) in
relation to the bowler's Grip midline, Grip Centerline and VAL (Vertical
Axis Line). In the diagrams the PAP used is of a bowler with coordinates
of 5 inches over and a 1/2 inch up. What is important to remember is
keeping the Pin position relative to the bowler's PAP consistent with
the diagrams. This is crucial to obtaining proper performance. For
lower rev rates placing the pin ½ inch closer to the PAP than the recommended
layouts will result in a larger hook potential. Depending on the bowler
the Pin position may look different from that shown in the diagrams.
The drilling instructions shown are for right handed bowlers. Reverse the drill instructions for left handed bowlers. The drilling instructions apply for 10 to 16 lb. balls.
Drilling #1 - Controllable Big Hook Motion
Ball Motion: Excellent length with strong arcing hook motion
Lane Condition: Medium to Heavy Oil
Flare Potential: Medium (3-5")
Pin Placement: Place pin at 4 1/2 " from PAP
CG Placement: Place CG within toward grip center
Weight Hole: If needed, place weight hole
approximately 4" over by 2" up from grip center |
 |
Drilling #2 - Controlled Arc
Ball Motion: Controlled arcing hook motion
Lane Condition: Light to Medium Oil
Flare Potential: Low (1-2")
Pin Placement: Place pin at 2-2 1/2" from PAP
CG Placement: Place CG within toward grip center
Weight Hole: If needed, place weight hole on PAP |
 |
Drilling #3 - Length with Strong Arc
Ball Motion: Early roll with smooth arcing hook motion
Lane Condition: Light Oil to Medium Oil
Flare Potential: Medium (2-4")
Pin Placement: Place pin at 5" from PAP
CG Placement: Place CG within toward grip center
Weight Hole: Place weight hole on PAP |
 |
Drilling #4 - Length with Sharp Backend
Ball Motion: Exceptional length with sharp backend motion
Lane Condition: Medium Oil
Flare Potential: Low (2-4")
Pin Placement: Place pin at 5 1/2" from PAP
Weight Hole: If needed, place weight hole
approximately 4" over by 2" up from grip center |
 |
Drilling #5 - Full-Roller Leverage Layout
For Full-Roller Ball Track Only
Ball Motion: Strong arcing ball motion
Flare Potential: Medium
Pin Placement: Place pin 33/8" from grip center at 7:30
CG Placement: Place CG within 1" of grip center |
 |
Top Weight - High top weight tends to make the ball skid further and store more energy through the front end of the lane. We recommend higher tops weights for drier lanes or bowlers with low ball speed. We further recommend for medium ball speeds or medium oil use medium top weights and for heavy oil or high ball speeds use low top weights.
Extra Holes - Might be required in some
drilling configurations. We recommend placing the hole on the positive
axis point or within 1" past the PAP. The use of balance holes more
than 1 inch away from the PAP care must be exercised in selecting the
placement to minimize flaring over the hole and must be done in consideration
of the type of drilling used along with the strength of the bowler's
release.
Static weights - As a rule we recommend that all balls be drilled with approximately 1/2 ounce of side weight to start. To calm down the backend reaction, gradually remove the positive side weight to 1/2 ounce negative to promote early hook.
Surface - The surface
of today's balls play an extremely important role in matching the bowler's
performance expectations with the lane conditions being played. To
create the best ball reaction, adjusting the surface by sanding or
polishing may be necessary. To add control and move the breakpoint
closer sand the ball's surface. The more aggressive the grit the earlier
the breakpoint and smoother the move off the breakpoint. To delay the
breakpoint and increase the flip potential in the backend of the lanes,
reduce the friction of the ball by polishing.
Bowling balls are interactive with their environment
and conditions during play. The surface picks up oil, dirt and debris
while being bowled. In time any ball's ability to perform will diminish
from this wear and tear. So cleaning the ball on a regular basis will
not only help to provide a consist reaction but prolong the life and
performance of the ball. Using a Microfiber towel before and after
each use will help minimize excessive oil, dirt and other unwanted
contaminants on the surface of the ball. We recommend using performance
ball cleaners for stubborn buildup.
Thanks for choosing one of the best brands in bowling,
and remember we're here when you have questions or need help; our support
line is ready with trained professionals to assist you in optimizing
your bowling experience. The support line number is 1-866-464-3791.
|
